Derby-Drivers Info / B&C

Haines Stampede

Ghain and Bang

Build Rules

Entry is free if you bring a car to compete then the driver, and one free pit pass will be issued at the gate.

Any RWD or FWD car no 4x4 or AWD, except lmperials, El Camino (or car truck style) or convertibles.

NOTE: lf you break any of these rules and we feel you're being deceptive to

create an advantage while doing it, you won't participate. lf you have any questions, please contact us.

Drivers are required to wear long pants, safety glasses or goggles and a helmet.

Remove the following before entering the facility: any flammable material, windows, plastic bumper covers, headlights, taillights, all chrome, and mirrors. lnterior must be swept clean of

debris and glass.

DISABLE OR REMOVE THE AIRBAG SYSTEM!

When using chain, it can only be a max of 3/8 diameter. If using wire, then only 3 strands of 9 gauge from Oregon Trail Livestock, or similar are permitted. Washers can be used toreinforce a hole you run wire or chain through MAX WASHER SIZE lS 2lN CIRCLE OR2X2 SQUARE.

Under the hood, you may take plastic fender wells out, strip plastic, and any other unneeded parts. The battery must be mounted inside the car securely and safely but cannot reinforce the car. You may need to lengthen the cables to reach it.

Engine swaps are allowed; they must be stock or close to stock. Simple headers are allowed.

Air cleaner is required incase of back fire.

The engine must be mounted near the stock position. The firewait may be cut out or pounded back behind the distributor.

Simple cable shifters are allowed.

No stock fuel tanks are permitted inside of the car. lf the stock tank is mounted in front of the rear axle it can stay. lf using a fuel cell or boat tank, then the cell or tank needs to be securely fastened to the floor with bolts. Your mount cannot re-enforce the car.

Radiator must be in factory position if you choose to run one.

All body bolts, mounts, and washers must be factory stock. No altering permitted. lf they are broken or rusted off, then you may add 3 loops of wire in the immediate area to secure the body just as the bolt did.

Doors can only be chained or wired with one chain or 3 strands of wire per hole. Do not chain/wire more than 8 places per door. The wire or chain at the bottom of the doors may go around the frame. Driver's door may be reinforced, if reinforcement is on the outside or inside, it cannot overlap the door seam by more than 3 inches. Grader blade or similar bracing i.e. 6 inch C-channel required on drivers door cannot extend past front or rear of the door by more than 6 inches. Driver door may be skifrned w plate instead of running door brace.

Trunks and hoods can only be chained or wired with no more than 8 total places on each. You may use chain, or 3 strands of wire per place. 2 of these places are permitted to go around the bumper and/or frame. Please create two 1O-inch holes or one 20-inch hole in the a o a hood and trunk for fire detection. Deck lids and/or tailgates must be in factory position on the car. You cannot smash down but you may remove the speaker deck from the car' You may cut the rear of the trunk lid off if you choose to. Do not tuck, wedge, pre-bend, notch, fold, or anything else you can think of to modify the trunk, hood, panels, or fenders' welding of washers to the body when using wire or chain ls ok MAX WASHER SIZE lS 2lN CIRCLE OR 2X2 SQUARE.

Note: You do not have to run a trunk lid gr hood but you must have something covering the mechanical fan if you run one' ***lf you choose to weld the hood you

may Use4locations max with a2x21l4in by 5 inches long angle bolted together with a max of 2 bolts per mounting point max. Mounts can only touch the hood and fender'

Any air filled tire. Must start with a stock wheel. An B" or smaller wheel center may be added' along with a valve stem protector. No studded tires'

DO NOT CREASE THE BODY OR FRAME. DO NOT FOLD THE TRUNK LID' IF YOU

CREASE THE BODY OR HAMMER THE BODY OR FRAME, BE PREPARED TO CHOP

THE WHOLE AREA OUT.

cages are driver / builder preference . Nothing extends into the trunk or past the firewall' Cage cannot be attached to frame. Cage can have plates welded to floor or body of car to allow it to be securely attached. You are required to have the factory seatbelt or a racing style harness. The inside of the driver door and anywhere in the drive r area of cage needs to be padded. CAGES MUST BE SAFE AND ARE SUBJECT To TECH' steering and suspension parts can only be the parts that came on the car or replaced with box store replacements. No purpose-built parts can be used in place of OEM parts lf you have to fab something together l.E. put a Ford rear end in a chevy car then suspension must be OEM to the car, or as close aS you can get. You can max out the suspension and weld it in place, cannot be reinforcement.

Bumper swaps are permitted must be oEM nothing after market. You can use a straight piece of open-ended square tube measuring 4"x4"x1/4" with a max length of 70"' You may weld the bumper directly tcj the front of the frame. No squaring or shortening. lnstead, use filler in the gaps, if necessary. ln either case, you may weld 2 pieces of 2"x 6" steel straps one on each side from the frame to the bumper, to ensure the bumper stays on' Do not use homemade, loaded, or seam welded bumpers unless using the above-mentioned square tube.

No additionalwelding unless for repair purposes and repair cannot be reinforcement, be prepared to explain to tech. lf you want to keep your number you need to call Kenny and pre-register.

Any questions please call or text Kenny Bain (541 ) 519-4825 or

Justin Prevo (541) 406-9325

Platinum Title Sponsor for all 3 Events :

Appliance and More

Baker City Chevrolet, Buick, GMC Inc.

Grocery Outlet- Baker City

Harney Rock

Eastern Oregon Rental

Gold Sponsor:

Premier Auto Body

Idaho Power

Sliver Sponsor:

Colwell Ranches

Baker Sanitary Service

Byrnes Oil

Triangle Cross Ranch

Tobacco Prevention - Baker Co.

Nick Conklin State Farm

Bronze Sponsor:

Wildhorse Resort & Casino

Les Bros Tire Service

Black Distributing

Precision Auto Repair

Welcome to Haines Stampede "Cut'er Loose"